The MC board fan is located on the left liner of the printer and is used to dissipate heat from the MC board.
The spare parts for the MC board fan include:
MC Board Fan × 1
Soft Screws × 4
The MC board fan produces abnormal noise.
The MC board fan malfunctions.
New MC Board Fan
H2.0 Allen Key
H1.5 Allen Key
Tweezers (recommended for easier installation of soft screws)
Specifications and quantities of screws involved in replacing the H2D MC board fan (it is recommended to keep the removed screws properly to avoid loss):
Specification | Image | Use | Position | Quantity | |
---|---|---|---|---|---|
BT3x8 | Fix the rear panel (marked with green square) | ![]() |
12 | ||
Fix the left side panel | ![]() |
![]() |
3 | ||
Fix the purge chute | ![]() |
1 | |||
Fix the AC board cover | ![]() |
1 | |||
M3x3(nut diameter 10mm) | Fix the front glass door | ![]() |
4 | ||
BT3x16 | Fix the auxiliary part cooling fan | ![]() |
2 | ||
ST3x3 | Fix the left side panel | ![]() |
2 | ||
ST3x8 | Fix the rear panel (marked with red circle) | ![]() |
11 | ||
ST3x12 | Fixed spool holder bracket (marked with yellow square) | ![]() |
2 |
IMPORTANT!
It's crucial to power off the printer before conducting any maintenance work, including work on the printer's electronics and tool head wires. Performing tasks with the printer on can result in a short circuit, leading to electronic damage and safety hazards.
During maintenance or troubleshooting, you may need to disassemble parts, including the hotend. This exposes wires and electrical components that could short circuit if they contact each other, other metal, or electronic components while the printer is still on. This can result in damage to the printer's electronics and additional issues.
Therefore, it's crucial to turn off the printer and disconnect it from the power source before conducting any maintenance. This prevents short circuits or damage to the printer's electronics, ensuring safe and effective maintenance. For any concerns or questions about following this guide, we recommend submitting a technical ticket regarding your issue and we will do our best to respond promptly and provide the assistance you need.
To remove the printer's rear panel, refer to the relevant information.
You can refer to this Wiki to remove the left side panel:Replace H2D Left/Right Side Panel
Use an H2.0 Allen key to remove 1 screw (BT3x8), then pull it down to remove the purge chute, until you can see the two clips of the purge chute, then take out the purge chute.
In addition to being fixed by the screws on the top, the purge chute also has two clips on the bottom that are fastened to the lining.
Disconnect the cables
Remove from the cable clips
After the removal
Note: While removing the AC board cover, take care to avoid interference with the top cables and the MC board heat sink.
The MC board fan is fixed to the inner liner with 4 soft screws. You can disconnect the MC board fan from the MC board first, and then pull out the four soft screws one by one from the outside of the left inner liner to remove the MC board fan.
Insert the AC board cover at an angle to avoid interference with the MC board heat sink. Push the cover upward, ensuring no cables are trapped underneath:
The auxiliary cooling fan cable and left side panel hall sensor cable should be positioned to the right of the AC board cover.
The heatbed cable and status indicator cable should exit through the bottom of the cover.
The MC-AC cable should pass through the small hole on the left side of the cover.
Refer to the following figure to buckle the cables into the corresponding clips one by one.
Note: When installing the purge chute, please pay attention to buckling both sides of the purge chute on the outside of the liner. If buckled on the inside, it may not be installed properly.
You can refer to this Wiki to install the left side panel: Replace H2D Left/Right Side Panel
Refer to the relevant Wiki guide for instructions on installing the H2D rear panel:Replace H2D Rear Panel
Connect the power cable and turn on the power. Run the device self-test as shown below, if no errors occur, the replacement was successful.
Otherwise, check all connections and try again. If the problem persists, contact the Bambu Lab service team for further assistance.
We hope the detailed guide provided has been helpful and informative.
If this guide does not solve your problem, please submit a technical ticket, we will answer your questions and provide assistance.
If you have any suggestions or feedback on this Wiki, please leave a message in the comment area. Thank you for your support and attention!